Woodworking gifts for sale

I’ve been busy making sawdust along with some projects that would make fine Christmas gifts.  Fill out the comment form and I’ll figure shipping.

Walnut and Maple End Grain Cutting Board

Beautiful and classic look of end grain walnut and maple.

Approximate Dimensions: 16″ x 12″ x 1-1/4″

5 available, $125/each


Padauk and Maple End Grain Cutting Board

Stunning contrast between the deep red/orange padauk and the light maple.

Approximate Dimensions: 18″ x 12″ x 1-1/4″

5 available, $149/each


Walnut and Zebrawood Keepsake Box

Walnut and zebrawood were meant to be together!  They compliment each other so nicely.

Approximate Dimensions: 11″ x 6″ x 6″



Cherry Keepsake Box


This box is made entirely out of cherry.  The lid has a strip of lighter sapwood along each edge as an accent.

Approximate Dimensions: 11″ x 6″ x 6″


Maple and Cherry Keepsake Box with Hinged Lid

The maple on this box has much character – undulating grain and iridescence.  The cherry in the lid is very straight rift sawn grained with a subtle bee’s wing figure.

Approximate Dimensions: 10″ x 6″ x 7″



Cherry and Birdseye Maple Keepsake Box

This box subtle grain patterns that will show timeless beauty.

Approximate Dimensions: 7″ x 4″ x 5″



Cherry and Birdseye Maple Keepsake Box

The front of this box has a fan shaped grain pattern on it.

Approximate Dimensions: 8″ x 4″ x 5″



6-Pack Carrier

Rustic looking scorched pine 6-pack carrier with bottle opener.  Holds 12 ounce bottles.  22 ounce bomber carriers and growler carriers coming soon!

10 available, $49/each HOME BREW NOT INCLUDED!


Wood Veneer Hammer

Veneer hammer 008

I made a veneer hammer patterned after the style Steve Latta uses.  I have a commercially made all metal hammer, but as Steve explained to me, a metal hammer gets too hot.  He sets his hammer in a shallow pan of water on a hot plate to keep the hot hide glue from sticking to it.  A wood head hammer stays cool to the touch.

This hammer is made from figured maple and cocobolo.  I did the maple work and I had The Boy turn the cocobolo handle.  I say he helped me make the hammer, he says I helped him make the hammer.  I said I could have turned the handle.  He says yeah, but what he did in an hour would have taken me all day and three pieces of wood.  Fair enough.

It is hard to see in the photos, but The Boy burnished in some accent rings into the handle with an old guitar string.  I think it turned out nice.

Veneer hammer 032

The metal squeegee portion of the hammer is a piece of 3/16″ brass stock.  I started with a square edge and rounded it over freehand.  Before I secured it into the maple head, I polished the brass on a buffing wheel.

Veneer hammer 012

The brass strip is attached to the head with epoxy, then three brass pins (visible at the bottom of the picture above) provided a mechanical connection should the epoxy ever fail due to heat or moisture issues.

The cocobolo handle is attached to the maple head with a wedged tenon.  For a touch of style, I made a brass wedge.

Veneer hammer 035

This hammer was used to veneer this mahogany fan pattern.  It worked just as well as Steve’s hammer and stayed cool to the touch.  What more could you ask for?




Dovetailed Router Plane Box

Once a year the Alaska Creative Woodworkers Association hosts a weekend event called Tools and Techniques. As president of the club, even I am not immune to doing demonstrations! I was asked to demonstrate cutting dovetails with a router jig.

Router plane box 002

I built this box as the completed sample to show while I did my demonstration. It also helped me get all the dovetails laid out ahead of time. I sized the box to use some of the odds and ends I had kicking around the shop. With a little fine tuning, it fits my Lee Valley router plane nicely. The plane is held in the box with some machine screws that go through the fence holes in the plane body. At some point I will make some long custom hold down nuts so you don’t have to reach all the way to the bottom of the box. Look for that project some time in the future!

Router plane box 004

The sides are maple which was left over from another box project. The left side has some interesting grain patterns and color from either a knot or a branch crotch. The top and bottom panels are 1/2” cherry veneer plywood. There is a little bit of curl in the panel I put on the lid. The finish is rattle can gloss lacquer. I knocked the gloss back with steel wool and wax. I used Brusso hinges and a jewelry box hasp from Home Depot. I wasn’t thrilled about the hasp in the beginning, but I think it looks good.

Router plane box 005

I cut the dovetails with my 24” Porter-Cable Omni Jig. I used the narrow pin router bit. All of the pins were the same size, except for the half pin at the joint of the lid and box. I made that pin 1/8” wider to account for the saw kerf when I cut the top off. To make it 1/8” wider, I used a drill bit as a spacer when I set up the guide fingers. Much easier than measuring! When I cut the lid off, I put a 1/16” thick 7-1/4” framing saw blade in my table saw. That left me a little meat to true up the join. I used sand paper glued to a granite slab and flattened the box like you would true the bed of a hand plane – figure eight pattern.

Since this was my display box, I have the twin box that I built during my demonstration. I haven’t cut the top off that one yet. Perhaps I will finish it as a gift with Christmas coming up soon.